Logo

U1160 Engine Trouble Code

U1160 Engine

When you check engine light came on code U1160 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the U1160 OBD-II Diagnostic Network (U) Trouble Code. So you should chech it on our car models.

U1160 if your catalytic convertor fails completely, you eventually won't be able to keep the car running its engine. Your gas mileage will also be not working properly, so you should try and fix it as soon as you can. Unfortunately, the average replacement cost is around $2,500 and you can't do it yourself unless you're an experienced mechanic service for your car.

U1160 Code Meaning :

U
OBD-II Diagnostic Network (U) Trouble Code For Engine
1
Fuel And Air Metering
1
Engine Oil Temperature Sensor Malfunction
6
Injection Pump Fuel Metering Control 'A' High (Cam/Rotor/Injector)
0
Exhaust Gas Recirculation Sensor B Circuit High

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

U1160 OBD-II Diagnostic Network (U) Trouble Code Description

U1160 engine trouble code is about Exhaust Gas Recirculation Sensor B Circuit High. Engine Oil Temperature Sensor Malfunction and Injection Pump Fuel Metering Control 'A' High (Cam/Rotor/Injector) causes most of code U1160.

Reason For U1160 Code

The reason of U1160 OBD-II Engine Trouble Code is Engine Oil Temperature Sensor Malfunction.

U1160 DTC reports a sensor fault, replacement of the sensor is unlikely to resolve the underlying problem. The engine error is most likely to be caused by the systems that the sensor is monitoring, but might even be caused by the wiring to the sensor itself.

How To Repair U1160 Code

Before starting let's see U1160 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access U1160 code stored in the ECU.
  • Technicians will note U1160 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

Engine data will be observed while the engine is operating and the throttle will be depressed looking for a change in the exhaust pressure sensor readings in comparison to bank 1.

This can result in damage to engine parts over duration of time. We consider that you seal the engine leaks right away if possible. Rising fuel usage can often be associated to a defect in how your engine generates fuel. When matched up with a check engine light in sight and other engine-associated symptoms, the issue can be even more critical. If you see that your vehicle is consuming more fuel, have it inspected and repaired by a mechanic.

Sometimes U1160 code comes with U116000 code.

Diagnosis Of Engine Error OBD Code U1160

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a U1160 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the U1160 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.